All local applications use the AETs and TCP/IP Ports configured via the Service/Installation Tool. The Field Service Engineer can configure the IP Address via the Service/Installation Tool. No Default AE Titles are provided. The AE Titles must be configured during installation. The local AET used by each individual application can be configured independently of the AET used by other local applications. If so configured, all local AEs are capable of using the same AET.
The EXAMPLE-PRINT-SERVER-MANAGEMENT is configured via the Configuration Service/Installation Tool as follows
Table E.4.4-1. AE Title Configuration Table
|
Application Entity |
Default AE Title |
Default TCP/IP Port |
|---|---|---|
|
PRINT-SCP |
Must be configured |
104 |
The AET, host names and port numbers of remote applications are configured using the EXAMPLE-PRINT-SERVER-MANAGEMENT Service/Installation Tool.
The EXAMPLE-PRINT-SERVER-MANAGEMENT Service/Installation tool must be used to set the AETs, port-numbers, host-names, Local Network Host Name, Router Address(Gateway), Sub-net Mask, IP-addresses (if no DHCP is used) and other capabilities for the remote Print SCUs. Multiple remote Print SCUs can be defined.
A large number of parameters related to Print Management, Communications and general operation can be configured using the Service/Installation Tool. The following table shows those configuration parameters relevant to DICOM communication. See the EXAMPLE-PRINT-SERVER-MANAGEMENT Configuration Service Manual for details on general configuration capabilities.
Table E.4.4-2. Configuration Parameters Table
|
Parameter |
Configurable (Yes/No) |
Default Value |
|---|---|---|
|
General Parameters |
||
|
Max PDU Receive Size |
Yes |
128 KB |
|
Max PDU Send Size(If the receiver supports a smaller Max PDU Receive Size then the Max PDU Send Size will be reduced accordingly for the duration of the Association. Max PDU Receive Size information is exchanged during DICOM Association Negotiation in the Maximum Length Sub-Item of the A-ASSOCIATION-RQ and A-ASSOCIATE-AC) |
Yes |
128 KB |
|
Time-out waiting for a acceptance or rejection response to an Association Request (Application level Timeout). |
Yes |
20 s |
|
Time-out waiting for a response to an Association release request (Application level Timeout) |
Yes |
30 s |
|
Time-out waiting for completion of a TCP/IP connect request (Low-level timeout) |
Yes |
20 s |
|
Time-out awaiting a Response to a DIMSE Request (Low level Timeout) |
Yes |
360 s |
|
Time-out for waiting for data between TCP/IP-packets (Low level Timeout) |
Yes |
30 s |
|
Maximum number of simultaneous Associations |
Yes |
8 |
|
Supported Transfer Syntaxes |
Yes |
Implicit VR Little Endian Explicit VR Little Endian |
|
Print Server Management |
||
|
Default Print parameters: Max density, Min Density, Contrast, Border Density, Trim, Magnification type, Smoothing factor, Polarity, Number of Copies, Cropping Algorithm, Orientation. |
Yes |
Configurable |
|
Number of times a failed print-job may be retried |
Yes |
3 |
|
Delay between retrying failed print-jobs |
Yes |
60s |
|
Printer Bit-depth Configurable: 8 or 12 |
Yes |
12 |
|
Custom Format |
No |
NA |
|
Media Type: Transparent (Film), Reflective (Paper) |
Yes |
Transparent |
|
Media size Configurable: 8IN X 10IN 11IN X 14IN 14IN X 14IN 14IN X 17IN |
Yes |
14IN X 17IN |
|
Maximum number of printable pixel matrix per supported Media size; see Note |
No |
8x10 - 2286x2836 11x14 - 4096x3195 14x14 - 4096x4108 14x17 - 4096x5120 |
|
Maximum number of collated films in a film session |
Yes |
12 |
|
Support N-EVENT-REPORT (On/Off for either Printer, Print Job or both). |
Yes |
On |
|
Handling of print jobs when requested Media Type and/or Film Size are not currently installed. The options are:
|
Yes |
Print on available media |
|
Print SCP time-out waiting for a SCU confirmation to a Print Status N-EVENT-REPORT |
Yes |
60 s |
|
Print SCP time-out waiting for a SCU confirmation to a Print Job N-EVENT-REPORT |
Yes |
60 s |
|
Supported Transfer Syntaxes (separately configurable for each remote SCU printer) |
Yes |
Implicit VR Little Endian Explicit VR Little Endian |
The adjustment (Magnification or Clipping) of the original image to the Printable image size is described in the Printer Service Manual.